1. Which dynamic routing protocol was developed to interconnect different Internet service providers? BGP*EIGRPOSPFRIP 2. Which routing protocol is limited to smaller network implementations because it does not accommodate growth for larger networks? OSPFRIP*EIGRPIS-IS 3. What two tasks do dynamic routing protocols perform? (Choose two.) discover hostsupdate and maintain routing tables*propagate host default gatewaysnetwork discovery*assign ...
Category: CCNA 2 v6.0
CCNA2 v6.0 Chapter 1 Exam Answers
1. A network administrator enters the command copy running-config startup-config. Which type of memory will the startup configuration be placed into? flashRAMNVRAM*ROM 2. Which packet-forwarding method does a router use to make switching decisions when it is using a forwarding information base and an adjacency table? fast switchingCisco Express Forwarding*process switchingflow process Fill in the ...
CCNA2 v6.0 Chapter 10 Exam Answers
1. A ping fails when performed from router R1 to directly connected router R2. The network administrator then proceeds to issue the show cdp neighbors command. Why would the network administrator issue this command if the ping failed between the two routers? The network administrator suspects a virus because the ping command did not work. ...
CCNA2 v6.0 Chapter 9 Exam Answers
1. Which method is used by a PAT-enabled router to send incoming packets to the correct inside hosts? It uses the destination TCP or UDP port number on the incoming packet.* It uses the source IP address on the incoming packet. It uses the source TCP or UDP port number on the incoming packet. It ...
CCNA2 v6.0 Chapter 2 Exam Answers
1. What are two advantages of static routing over dynamic routing? (Choose two.) Static routing is more secure because it does not advertise over the network.*Static routing scales well with expanding networks.Static routing requires very little knowledge of the network for correct implementation.Static routing uses fewer router resources than dynamic routing.*Static routing is relatively easy ...
CCNA2 v6.0 Chapter 4 Exam Answers
1. A network designer must provide a rationale to a customer for a design which will move an enterprise from a flat network topology to a hierarchical network topology. Which two features of the hierarchical design make it the better choice? (Choose two.) lower bandwidth requirementsreduced cost for equipment and user trainingeasier to provide redundant ...
CCNA2 v6.0 Chapter 7 Exam Answers
1. In which configuration would an outbound ACL placement be preferred over an inbound ACL placement? when the ACL is applied to an outbound interface to filter packets coming from multiple inbound interfaces before the packets exit the interface*when a router has more than one ACLwhen an outbound ACL is closer to the source of ...
CCNA2 v6.0 Chapter 3 Exam Answers
1. Which dynamic routing protocol was developed to interconnect different Internet service providers? BGP*EIGRPOSPFRIP 2. Which routing protocol is limited to smaller network implementations because it does not accommodate growth for larger networks? OSPFRIP*EIGRPIS-IS 3. What two tasks do dynamic routing protocols perform? (Choose two.) discover hostsupdate and maintain routing tables*propagate host default gatewaysnetwork discovery*assign ...
CCNA2 v6.0 Chapter 6 Exam Answers
1. What are three primary benefits of using VLANs? (Choose three.) security*a reduction in the number of trunk linkscost reduction*end user satisfactionimproved IT staff efficiency*no required configuration 2. Which type of VLAN is used to designate which traffic is untagged when crossing a trunk port? datadefaultnative*management 3. A network administrator is determining the best placement ...
CCNA2 v6.0 Chapter 5 Exam Answers
1. Which statement describes the port speed LED on the Cisco Catalyst 2960 switch? If the LED is green, the port is operating at 100 Mb/s.*If the LED is off, the port is not operating.If the LED is blinking green, the port is operating at 10 Mb/s.If the LED is amber, the port is operating ...